Main tank textured polyethylene (L): 2.000.

Clean water textured polyethylene (L): 250.

Application width (m): 25

Nozzle spacing (mm): 500

Hydraulic suspension by nitrogen accumulator

Auxiliary lighting for night spraying

Working height of the bars (m):

• Minimum: 0.60
• Maximum: 2.25

Control valves panel for spraying, incorporation, and supply.

Spraying pump: UDOR membrane, 170 L/min at 550 rpm (hydraulic motor drive).

Spraying control: 7-section electronic.

On-board computer: Smart Jan controller.

Nozzle holder: triple Arag.

Spray tips: Teejet.

With ARAG incorporator - capacity 30 L in polyethylene.

Hydraulic activated by electrovalves.

Load Sensing hydrostatic direction.

Bidirectional.

Individual suspension, which provides lower rate of slippage, improving the copy of the terrain and giving greater stability to the machine.

• Brake: Hydraulic drive with ventilated disc and calipers on the four wheels.
• Stationary brake, spring applied/hydraulic release.
• Tie rods: With rubberized pins fixed through bolts.

Tire: 12-4x36 TM93 12 canvas with tube.

• Suspension: Independent active pneumatic.
• Tie rods: With rubber bushings, fixed by screws.
• Clean tracks and Fenders: Tubular with adjustment according to the gauge on the four wheels.

MWM SÉRIE 12 – 4.10 TCA MAR-I 130CV@2.200rpm e 550Nm@1400rpm Turbo Aftercooler.

Mechanical engine, which meets the MAR-1 legislation that defines the limits of pollutant emissions.

Lower fuel consumption;

Polyethylene fuel tank (L): 180

Lower fuel consumption.

Box: Eaton FS 4205 B (5 speeds forward and 1 reverse).

Transfer case with cast iron housing, heat treated gears with high resistance, reduction (1.33:1).

Spring applied stationary brake with hydraulic release at the transfer box exit.

Differential: Dana 80 Autoblocating 1:4.625 Lubricant Oil Type 140 85W140 API GL 5-LS - 5 liters.

• Wheel transmission: ASA 140 Chain SAE 680 Oil Bath - 5 liters.
• Application Speed (1800 rpm): in 3rd gear 14.3 km/h.
• Displacement speed: up to 42.2 km/h always with the machine empty.

1                           6

2                           11,1

3                           19,8

4                           33

5                           42,2

Re                         7,6

Weld-free stringers made of high-strength steel, thus enabling greater resistance to traction, torsion, bending, and fatigue, extending the component's useful life.

Other chassis elements are built in structural steel and bolted to the stringers, allowing their exchange in case of need.

The gangways allow easy access for maintenance of the engine and hydraulic tank.

Under cushions for vibration damping.

Pressurized with ecologic digital air-conditioning and hot air.

Anatomic seat with electro-pneumatic suspension.

Left side unilateral door.

Green 6 mm tinted windshield with black band, door and rear windows tinted 6 mm tinted smoked with black band.

Radio with USB input.

Compartment for ECU's, 12 and 5 VDC sockets.

Giroflex and LED headlights.

Main tank textured polyethylene (L): 2.650.

Clean water textured polyethylene (L): 250.

Application width (m): 25, 27 and 30.

Nozzle spacing (mm): 500.

Hydraulic suspension by nitrogen accumulator.

Auxiliary lighting for night spraying.

Working height of the bars (m):

• Minimum: 0.60.
• Maximum: 2.42.

Control valves panel for spraying, incorporation, and supply.

Spraying pump: UDOR membrane, 170 L/min at 550 rpm (hydraulic motor drive).

Spraying control:

• Electronic 7 sections for 25 and 27 meters bars.
• Electronic 11 sections for 30-meter bars.

On-board computer: Smart Jan controller.

Nozzle holder: triple Arag.

Spray tips: Teejet.

By centrifugal pump hydraulically driven.

Suction height 7.62 m/25 ft.

Capacity 780 l/min with Ø2" inlet and outlet with quick coupling.

Polypropylene impeller with stainless steel insert.

Washing: With NIAGARA incorporator – capacity 30 L in polyethylene.

Hydraulic activated by electrovalves.

Load Sensing hydrostatic direction.

Bidirectional.

When the autopilot is engaged, the rear wheels are aligned.

Above 20 km/h, the rear wheels are aligned, increasing the machine's stability.

When reaching 15 km/h, the rear wheelset copies the front wheelset track again, optimizing maneuvers by reducing the machine's turning radius.

The system has a diagnostic screen of the wheelset position sensors, for visualization and calibration.

Individual suspension, which provides a lower rate of slippage, improving the copy of the terrain and giving greater stability to the machine.

• Brakes: Hydraulic drive with ventilated disc and calipers on all four wheels.
• Stationary brake, spring applied/hydraulic release.
• Tie rods: With rubber bushings, fixed by screws.

Tire: 12-4x36 TM93 12 canvas with tube.

Suspension: Independent active pneumatic.

Tie rods: With rubberized pins fixed through bolts.

Clean tracks and Fenders: Tubular with adjustment according to the gauge on the four wheels.

MWM SÉRIE 12 – 4.12 TCE MAR-I 160CV@2.200rpm e 640Nm@1.500rpm, Turbo, Aftercooler.

Mechanical engine, which meets the MAR-1 legislation that defines the limits of pollutant emissions.

Torque control and gear recognition, avoiding stress peaks in the transmission and other components.

Lower fuel consumption.

Torque control in 1st and reverse gears, limited to 550 Nm, to avoid torque peaks in the transmission system.

Transfer case with cast iron housing, heat treated gears with high resistance.

Stationary brake at the transfer box output.

Gearbox: Eaton FS 4205 B (5 speeds forward and 1 reverse).

Differential: Dana 80 Autoblocating 1:4.625. Lubricant Oil Type 140 85W140 API GL5-LS - 5L.

Wheel transmission: ASA 140 Chain Oil Bath SAE 680 - 8L.

Application Speed (1800 rpm): in 3rd gear 14.7 km/h.

Displacement speed: up to 43.04 km/h always with the machine empty.

Weld-free stringers made of high-strength steel, thus enabling greater resistance to traction, torsion, bending, and fatigue, extending the component's useful life.

Other chassis elements are built in structural steel and bolted to the stringers, allowing their exchange in case of need.

The gangways allow easy access for maintenance of the engine and hydraulic tank.

Under cushions for vibration damping.

Pressurized with ecologic digital air-conditioning and hot air.

Anatomic seat with electro-pneumatic suspension.

Left side unilateral door.

Green 6 mm tinted windshield with black band, door and rear windows tinted 6 mm tinted smoked with black band.

Radio with USB input.

Compartment for ECU's, 12 and 5 VDC sockets.

Giroflex and LED headlights.